Can you backwash too often

If you have already backed washed your pool and the pressure is still high, check out our article: 8 Reasons Filter Pump Pressure is High And How to Fix. If your pool contains an unusually high level of dirt for instance, as a result of a nearby construction site, a protracted period of being untended and uncovered, or possibly from runoff caused by flooding it may be advisable to by-pass the filter entirely. This is also the case if your water had, or has had, an algae problem.

Live algae easily pass through the filter sand and re-enters the pool. And the same goes for dead algae following a shock treatment.

You can read more on preventing algae here. In these cases, instead of vacuuming and backwashing, it may be better to vacuum directly to WASTE, and to send the vacuumed water directly down into the drain. Pool Sand Filter. Replacement Filter Sand. Do you ever need to change the sand in a sand filter?

My semi above ground liner pool is constantly murky. The filter seems to be working fine and has a lot of pressure when you see water going through but the pressure gauge is always sitting just above zero? The filter is only about 8 years old. Yep you should change the sand. Most filter manufacturers recommend every years. Every 5 years is fine. A very awesome blog post. We are really grateful for that blog publish.

I used to be exactly looking for. Appreciate such publish and please keep writing. Great work. Hi there. I had my sand changed about a year ago. I did have some green algie, so shocked and vacuumed, but not to waste.

Since then it has been a constant cycle of shock, yellowey algie or something sat at the bottom, vacuum and whilst vacuuming the returned water is cloudy, so need to shock again. I have back washed and rinsed until clear is seen in the peep hole. Can you tell me what is could be?

Then again I only back washed once twice a month max during the season. I primarily vacuum with the robot so not a lot of debris ended up in the filter. Thanks for the tip! This is very well written and informative!

We have a new filter and pump that was just installed for out 30, gal inground pool. The previous owner told me to only backwash if I saw air bubbles coming from the jet.

Thank you for taking the time to write and post this! New Content Conversations Unanswered threads New media. Current visitors. Forum Rules. Can you backwash Sand Filter too often? JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser. LifeTime Supporter. Jun 16, Long Island, NY. PSI is steady at In May we had the sand in the filter replaced as the pool was shut down for 8 years and whatever was in the filter turned to Muck.

It seems to be doing a great job, as the water is crystal. So should I just be using the waste to lower the water level? Turn on the pump and continue to run under normal operating conditions. If you backwash your pool too much i. Over time, the sand inside the filter loses its coarseness and becomes smooth and round. This makes it very hard for the sand to catch really small debris particles. Every 3 to 5 years you should change the sand in a pool filter.

Sand filters are perfect filters for almost any type of pool, although as previously mentioned they do require a bit of maintenance. As you now know, backwashing is easy to do and should become part of your regular pool maintenance schedule. Remember, for piece of mind always keep an eye on the pressure in your filter and if it gets too high, go ahead and backwash your sand filter. A clean filter is key to a clean and healthy pool and will help you maintain the highest water quality possible so your family and friends can enjoy your pool during the summer.

We cut out all the fluff and confusion of pool maintenance and provide Gold Coast residents with pool servicing and advice. Your email address will not be published. Last Updated: 25th August, The short answer is yes you can backwash your swimming pool filter system too much. I can cause alot of problems and issues down the road. Only backwash when your sand filter system needs it, when the psi gauge gets 8 - 10psi over the "just back washed" pressure. By back washing too much you take this away.

Monserrate Kulkarni Professional. Do you run pool pump while swimming? Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

Darlene Piedrola Professional. Should I run my pool pump when it rains? Note: If you had a lot of rain , your pool may have extra water. This is good if you need to vacuum at a lot of debris off the bottom of your pool to waste.

Katy Tippl Professional. How often should a pool be shocked? Always make sure that the filter system is running while shocking the pool. Some pool owners choose to shock their pools once every weeks as normal maintenance.

This is a great way to keep your chlorine level up and prevent algae growth. Anatoly Thomson Explainer. How many hours should I run my pool pump? Swimming pool pumps should be run an average 8 hours a day to properly circulate and clean your water. The pump should push your entire pool in gallons in this 8 hour period of time. However, often times swimming pool pump horse power is overrated for their size swimming pool.

Wenhua Szelmeczk Explainer. Why is my pool dirty after I vacuum it? If dirt is reappearing at the bottom of your swimming pool after you've vacuumed it your pool's filter may be working poorly.

Pool filters often work poorly because they're in need of cleaning.